NIBE SMO 40

NIBE AXC 30

Accessory card.

NIBE IU 3 kW

Electric heating element

NIBE SOLAR 42

NIBE SOLAR 42 enables solar heating with your heat pump. With additional solar panels and VPBS you get a complete system.

NIBE F135

The NIBE F135 is an exhaust air module designed for docking to a NIBE air/water heat pump and a NIBE indoor module (VVM) or control module (SMO). The NIBE F135 uses the heat that is found in the house’s ventilation air to heat the house and hot water, at the same time as ventilating the house. In installations with cooling, hot water and cooling can be produced at the same time. The exhaust air module provides an improved seasonal performance factor and has a low noise level and high ventilation capacity. The NIBE F135 is easy to control through the heat pump’s indoor module. Thanks to smart technology, the product gives you control over your energy consumption and will be a key part of your connected lifestyle. The efficient control system automatically adjusts the indoor climate for maximum comfort, and you do nature a favour at the same time.

NIBE POOL 40

An accessory that allows pool heating using heat pump. Max 18 kW. The heat pump controls the reversing valve, pool circulation pump and any heating circuit circulation pumps via POOL 40.

NIBE MODBUS 40

A NIBE heat pump can be controlled and monitored by external Modbus equipped equipment.

NIBE IU 6 kW

Electric heating element

NIBE IU 9 kW

Electric heating element

NIBE RMU 40

With RMU 40 you can control and monitor your Nibe heat pump from another room in the house.

NIBE K11

Connections box with thermostat and overheating protection

NIBE CPD 11-25/75 (UPM2 K 25-75)

NIBE ELK 213

The NIBE ELK 213 is an electric heater designed for heating detached houses or smaller rental homes, as well as indirect heating of hot water. The NIBE ELK 213 can be installed together with a boiler, accumulator tank or heat pump. When installed together with a heat pump, for example, the electric heater automatically switches on to provide supplementary heating when the heating demand is greater than the heat pump’s capacity.

NIBE ELK 15

ELK 15 is an immersion heater primarily intended for installation together with heat pump for heating. NIBE ELK 15 contains overheating protection and contactors to externally regulate the two power groups, 5.0 and 10.0 kW.

NIBE ELK 26

ELK 15 is an immersion heater primarily intended for installation together with heat pump for heating houses or

NIBE EME 20

Communication and control. EME 20 is used to enable communication and control between the inverter for solarcells and heat pump/indoor module/control module.

NIBE ELK 42

Electric boilers for additional heating for ground source heat pumps.

NIBE EMK 300

Energy measurement kit for indoor unit.

NIBE EMK 500

Energy measurement kit for indoor unit.

NIBE ERS 30-400

The NIBE ERS 30-400 is a heat recovery ventilation unit with high temperature efficiency up to 94% and low energy consumption. The heat recovery ventilation unit is used in houses with areas up to approx. 350 m2. The NIBE ERS 30-400 is designed for installation with a NIBE ground source heat pump or a NIBE air/water heat pump for a complete heating and ventilation system. The heat recovery ventilation unit is easily controlled by the heat pump. Thanks to smart technology, the product gives you control over your energy consumption and will be a key part of your connected lifestyle. The efficient control system automatically adjusts the indoor climate for maximum comfort, and you do nature a favour at the same time.

NIBE HR 10

Auxiliary relay HR 10 is a connection box housing a contactor and a rotary selector switch. It is used to control external 1 to 3-phase loads such as oil burners, immersion heaters and pumps.

NIBE HR 20

NIBE HTS 40

HTS 40 is an accessory that records humidity and temperature.

NIBE ECS 40

ECS 40 is used when heat pump is installed in houses with up to four different climate systems that require different flow line temperatures, for example, in cases where the house has both a radiator system and an under floor heating system.

NIBE ECS 41

Extra heating circuit (recommended 80-250 m2 floor heating). ECS 41 is used when heat pump is installed in houses with up to four different climate systems that require different flow line temperatures, for example, in cases where the house has both a radiator system and an under floor heating system.

NIBE RTS 40

Room sensor used to obtain a more even indoor temperature. RTS 40 has up to three functions: Show current room temperature in the heat pump's display. Option of changing the room temperature in °C. Makes it possible to change/stabilise the room temperature.

NIBE SMS 40

GSM remote control. Settings via the heat pump’s display. Adjustment of operation mode via SMS. SMS notifications upon alarm and e g power failure. Status information via SMS.

NIBE SOLAR 40

NIBE SOLAR 40 enables solar heating with your heat pump. With additional solar panels and VPAS you get a complete system.

NIBE VPB 500-1000

The NIBE VPB 500/750/1000 is an efficient, copperlined hot water tank with a wide range of applications which is developed for connection to a heat pump, gas or oil boiler. The NIBE VPB 500/750/1000 has insulation made of Neopor and polyester fleece, which provides low energy loss. The insulation and outer shell are detachable to facilitate installation. The NIBE VPB 500/750/1000 is designed for buildings with large hot water requirements and can be connected in parallel for maximum capacity.

NIBE VST 11

Provides the heat pump together with SMO 10 to prioritise hot water charging on systems with floating condensing. This also requires a hot water accumulator, for ex. NIBE VPA. Hot water control for max.electric charge output: 18 kW

NIBE VST 20

Makes hot water priority possible at large heat pump outputs. (charging power between 15 and 40 kW), together with an SMO 10 and F1330-40. This also requires a hot water accumulator, for example, NIBE VPA.